Datamax Printer Troubleshooting Manual May Be
No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser's personal use, without the expressed written permission of Datamax Corporation.All rights reserved. In no event will Licensor or its suppliers be liable for any damages or loss, including direct, incidental, economic, special, or consequential damages, arising out of the use or inability to use the Firmware (Software).Information in this document is subject to change without notice and does not represent a commitment on the part of Datamax Barcode Products Corporation. The firmware (Software) is protected by applicable copyright laws and Licensor retains all rights not expressly granted. The User agrees not to, and not to authorize or permit any other person or party to, duplicate or copy the EPROM’s or the information contained in the EPROM’s. If 3122 Lost Wax Resin 3D Printer Castable UV Curable Resin 405nm Jewelry.Allegro2, SEAQ, and PC Batch are trademarks of Datamax Barcode Products Corporation.As an Energy Star Partner, Datamax Corporation has determined that this product meets the Energy Star guidelines for energy efficiency.Firmware (Software) Agreement: The enclosed Firmware (Software) resident in the EPROM’s is owned by Licensor or its suppliers and is licensed for used only on a single printer in the user’s Trade or Business.
Disconnect power supply cord in case of emergency.3. This unit is intended for indoor use only.2. Falls kein Kabel mitgeliefert wurde, bitte Folgendes bei der Anschaffung eines Kabels beachten:Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat sowie eine IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250 Volt.1. Bei Gefahr, Kabel aus der Steckdose herausziehen3. Nur für Gebrauch innerhalb eines Gebäudes geeignet.2.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Your Barcode Printer has been designed to give you many years of safe, reliable service. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Ribbon Loading Instructions. Label Loading Instructions. Tear-off Assembly Installation.Using the Printer Control Panel.Media Installation. If the power cord becomes damaged or frayed replace it immediately.∙ Do not insert anything into the ventilation slots or openings on the Printer.∙ Only qualified, trained service technicians should attempt to repair your Printer.Introduction. If you are unsure, check with your dealer or with your local power company.∙ Do not place the power cord where it will be walked on.
Programming Examples.♦ Creating Labels Using Internal Batch SoftwareThe Printer used with a LINK CRT.Formatting and Printing Labels.Create/Modify Label Screen. Sample Installations.Switch Settings. Interfacing to the Printer. Checking Voltage Selection.
Place the label roll on the Supply Mount and slide the Retainer firmly against it.5. Slide the Retainer to the outer edge of the Supply Mount.4. Slide the Media Guide to the outer edge of the guide and rotate it to the ‘down’ position.3. Disengage the Printhead by rotating the Head-Lift Lever counterclockwise to the ‘up’ position.2.
The gauge behind and below the Printhead can be viewed for making this adjustment. Engage the Printhead by rotating the Head-Lift Lever clockwise to the ‘down’ position.If the Media is not sensing, try adjusting the sensor position by turning the adjustment knob for the movable sensor. Route the Media Guide ‘up’ and slide it to the edge of the Media.7.
In this case, check the threading of the Media around the bottom of the upper and lower Media Guides.If the paper feeds forward only about 2.5" (64mm) each time you press the Feed Button, and does not seem to be stopping on a label edge, the Ribbon on/off Switch, (shown in Figure 1-5) was probably turned on without Thermal-Transfer Ribbon being installed.
0 kommentar(er)
